Recently Published Issues

See all

Materials Science Weekly Newsletter

Get the latest materials science news straight to your inbox every week - sign up now!

Recently Published Articles

  1. Sintering Behavior of Lanthana-Bearing Nanostructured Ferritic Steel Consolidated via Spark Plasma Sintering

    Somayeh Pasebani, Indrajit Charit, Darryl P. Butt, James I. Cole, Yaqiao Wu and Jatuporn Burns

    Article first published online: 3 AUG 2015 | DOI: 10.1002/adem.201500294

    Thumbnail image of graphical abstract

    The work reported herein investigates the effect of milling time on the spark plasma sintering kinetics and microstructural evolution of 14LMT alloy, a nanostructured ferritic steel, containing lanthanum instead of yttrium. The predominance of grain boundary diffusion during sintering is noted. Microstructure is characterized by SEM/EBSD and TEM, and mechanical property by Vickers microhardness technique.

  2. The Organic Power Transistor: Roll-to-Roll Manufacture, Thermal Behavior, and Power Handling When Driving Printed Electronics

    Francesco Pastorelli, Thomas M. Schmidt, Markus Hösel, Roar R. Søndergaard, Mikkel Jørgensen and Frederik C. Krebs

    Article first published online: 3 AUG 2015 | DOI: 10.1002/adem.201500348

    Thumbnail image of graphical abstract

    The footprint of organic electronic technologies is important when united in complex circuitry. We describe the area requirements for roll-to-roll processed electrochromics, solar cells, and printed organic power transistors in joint operation of a large area window shading application and find that organic power transistors and OPVs can drive electrochromics while taking up very little area.

  3. Comparison of TiAl-Based Intermetallics Joints Brazed with Amorphous and Crystalline Ti–Zr–Cu–Ni–Co–Mo Fillers

    Li Li, Xiaoqiang Li, Zhifeng Li, Ke Hu, Shengguan Qu and Chao Yang

    Article first published online: 31 JUL 2015 | DOI: 10.1002/adem.201500190

    Thumbnail image of graphical abstract

    The room temperature shear strength of the joint brazed with the amorphous filler is always much higher than that with the crystalline filler, and the maximum joint shear strength is 202 MPa at a brazing temperature of 1 000 °C. The differences in performance of the joints are related to the microstructure characteristics of the brazing seams.

  4. Fabrication of Coaxial Wet-Spun Graphene–Chitosan Biofibers

    Azadeh Mirabedini, Javad Foroughi, Brianna Thompson and Gordon G. Wallace

    Article first published online: 22 JUL 2015 | DOI: 10.1002/adem.201500201

    Thumbnail image of graphical abstract

    The novel technique of coaxial wet-spinning is employed for the fabrication of electroactive biofibres of chitosan/graphene oxide in a basic coagulation bath. As-prepared fibres were found to be cytocompatible with good electrical conductivity and mechanical properties. The results imply that the developed fibres hold a great promise in applications such as drug delivery, batteries and tissue scaffolds in nearby future.

  5. Preparation of Fine-Grained and High-Strength Mg–8Li–3Al–1Zn Alloy by Accumulative Roll Bonding

    Tianzi Wang, Haipeng Zheng, Ruizhi Wu, Jinliang Yang, Xudong Ma and Milin Zhang

    Article first published online: 22 JUL 2015 | DOI: 10.1002/adem.201500211

    Thumbnail image of graphical abstract

    Fine-grained and high-strength Mg–8Li–3Al–1Zn alloy is obtained using accumulative roll bonding (ARB) technique. The ARB refines the grains and causes the phase distribution to be scattered. With the increase of ARB passes, the σ0.2,σb, and hardness values are enhanced, whereas the elongation value first decreases, then slightly increases with the increase of ARB passes.

SEARCH

SEARCH BY CITATION