Getting started with open‐hardware: Development and control of microfluidic devices
Colour Online: See the article online to view Figs. 1–4 in colour.
Abstract
Understanding basic concepts of electronics and computer programming allows researchers to get the most out of the equipment found in their laboratories. Although a number of platforms have been specifically designed for the general public and are supported by a vast array of on‐line tutorials, this subject is not normally included in university chemistry curricula. Aiming to provide the basic concepts of hardware and software, this article is focused on the design and use of a simple module to control a series of PDMS‐based valves. The module is based on a low‐cost microprocessor (Teensy) and open‐source software (Arduino). The microvalves were fabricated using thin sheets of PDMS and patterned using CO2 laser engraving, providing a simple and efficient way to fabricate devices without the traditional photolithographic process or facilities. Synchronization of valve control enabled the development of two simple devices to perform injection (1.6 ± 0.4 μL/stroke) and mixing of different solutions. Furthermore, a practical demonstration of the utility of this system for microscale chemical sample handling and analysis was achieved performing an on‐chip acid–base titration, followed by conductivity detection with an open‐source low‐cost detection system. Overall, the system provided a very reproducible (98%) platform to perform fluid delivery at the microfluidic scale.
Number of times cited: 18
- Xuzhi Zhang, Mengshi Huang, Jun Zhao, Jingquan Liu, Wenrong Yang and Keming Qu, Monitoring acid-base, precipitation, complexation and redox titrations by a capacitively coupled contactless conductivity detector, Measurement, 116, (458), (2018).
- Pawel L. Urban, Prototyping Instruments for the Chemical Laboratory Using Inexpensive Electronic Modules, Angewandte Chemie International Edition, 57, 34, (11074-11077), (2018).
- Pawel L. Urban, , Angewandte Chemie, 130, 34, (11241-11245), (2018).
- Pavel Kubáň and Peter C. Hauser, Contactless conductivity detection for analytical techniques— Developments from 2014 to 2016, ELECTROPHORESIS, 38, 1, (95-114), (2016).
- Michael D. M. Dryden, Ryan Fobel, Christian Fobel and Aaron R. Wheeler, Upon the Shoulders of Giants: Open-Source Hardware and Software in Analytical Chemistry, Analytical Chemistry, 89, 8, (4330), (2017).
- Joshua M. Pearce, Emerging Business Models for Open Source Hardware, Journal of Open Hardware, 1, 1, (2017).
- Kara Brower, Robert Puccinelli, Craig J. Markin, Tyler C. Shimko, Scott A. Longwell, Bianca Cruz, Rafael Gomez-Sjoberg and Polly M. Fordyce, An Open-Source, Programmable Pneumatic Setup for Operation and Automated Control of Single- and Multi-Layer Microfluidic Devices, HardwareX, (2017).
- Karankumar C. Dhankani and Joshua M. Pearce, Open source laboratory sample rotator mixer and shaker, HardwareX, 10.1016/j.ohx.2016.07.001, 1, (1-12), (2017).
- C. Zhang, B. Wijnen and J. M. Pearce, Open-Source 3-D Platform for Low-Cost Scientific Instrument Ecosystem, Journal of Laboratory Automation, 21, 4, (517), (2016).
- Jan Dolinay, Petr Dostalek and Vladimir Vasek, Arduino Debugger, IEEE Embedded Systems Letters, 8, 4, (85), (2016).
- Seyed Ali Mousavi Shaegh, Fabio De Ferrari, Yu Shrike Zhang, Mahboubeh Nabavinia, Niema Binth Mohammad, John Ryan, Adel Pourmand, Eleanor Laukaitis, Ramin Banan Sadeghian, Akhtar Nadhman, Su Ryon Shin, Amir Sanati Nezhad, Ali Khademhosseini and Mehmet Remzi Dokmeci, A microfluidic optical platform for real-time monitoring of pH and oxygen in microfluidic bioreactors and organ-on-chip devices, Biomicrofluidics, 10.1063/1.4955155, 10, 4, (044111), (2016).
- J. M. Pearce, N. C. Anzalone and C. L. Heldt, Open-Source Wax RepRap 3-D Printer for Rapid Prototyping Paper-Based Microfluidics, Journal of Laboratory Automation, 10.1177/2211068215624408, 21, 4, (510-516), (2016).
- Pedro Novo, Margherita Dell'Aica, Dirk Janasek and René P. Zahedi, High spatial and temporal resolution cell manipulation techniques in microchannels, The Analyst, 141, 6, (1888), (2016).
- BAS WIJNEN, EMILY E. PETERSEN, EMILY J. HUNT and JOSHUA M. PEARCE, Free and open‐source automated 3‐D microscope, Journal of Microscopy, 264, 2, (238-246), (2016).
- Wendell K. T. Coltro, Maria F. Mora and Carlos D. Garcia, Instrumental Aspects of Food Analysis by Electrochemical Methods, Agricultural and Food Electroanalysis, (443-477), (2015).
- Tom Baden, Andre Maia Chagas, Greg Gage, Timothy Marzullo, Lucia L. Prieto-Godino and Thomas Euler, Open Labware: 3-D Printing Your Own Lab Equipment, PLOS Biology, 13, 3, (e1002086), (2015).
- Pawel L. Urban, Universal electronics for miniature and automated chemical assays, The Analyst, 10.1039/C4AN02013H, 140, 4, (963-975), (2015).
- Handy Chandra, Spencer Allen, Shane Oberloier, Nupur Bihari, Jephias Gwamuri and Joshua Pearce, Open-Source Automated Mapping Four-Point Probe, Materials, 10.3390/ma10020110, 10, 2, (110), (2017).
